The · W e s t o n e · Forums
Would you like to react to this message? Create an account in a few clicks or log in to continue.

ISO Bendmaster setup videos

2 posters

Go down

Bendmaster - ISO Bendmaster setup videos Empty ISO Bendmaster setup videos

Post by drsyn67 Wed Jan 03, 2018 8:16 pm

Has anyone made or seen a well-filmed setup of the beloved/hated Bendmasters  (FT or Deluxe)?
drsyn67
drsyn67
Senior Member

Number of posts : 451
Age : 57
Location : Jacksonville, FL
Registration date : 2012-02-08

http://www.markcountscreative.com

Back to top Go down

Bendmaster - ISO Bendmaster setup videos Empty Re: ISO Bendmaster setup videos

Post by Barry Wed Jan 03, 2018 9:41 pm

I've not had any issues with any of the Mats' trems. (note that's tremolo bridge, NOT that God awful barrel saddle thingy). A trem setup is pretty much the same on most guitars, string versus spring balancing act.

Are you experiencing grief? Corsair is the bridge expert. geek

_________________
"A little song. A little dance. A little seltzer down your pants." -Chuckles the Clown
Bendmaster - ISO Bendmaster setup videos Guitar10
GUITARS : https://legend.barryeames.com
MUSIC/PIX/VIDEOS: https://getback.barryeames.com (including Spectrum ST)
Barry
Barry
Hero, Legend, and all round good guy

Number of posts : 8796
Age : 79
Location : Port Weller, St. Catharines, Canada
Registration date : 2009-05-01

https://legend.barryeames.com

Back to top Go down

Bendmaster - ISO Bendmaster setup videos Empty Re: ISO Bendmaster setup videos

Post by drsyn67 Wed Jan 03, 2018 10:44 pm

Thanks, Barry... re-watched several Floyd Rose setups again. I need practice (and to remember to stretch strings) Crying or Very sad
drsyn67
drsyn67
Senior Member

Number of posts : 451
Age : 57
Location : Jacksonville, FL
Registration date : 2012-02-08

http://www.markcountscreative.com

Back to top Go down

Bendmaster - ISO Bendmaster setup videos Empty Re: ISO Bendmaster setup videos

Post by Barry Thu Jan 04, 2018 9:22 am

Atta boy! Dance 1

"Stretching" the strings really refers to applying enough manual pull on the string so the windings on the post (primary) settle in nice and snug. That prevents their slipping and going flat when you're trying to tune up.

And just a quick note about the locking plates: Do not over tighten them or you'll end up with mini-guillotines. Or worse, you'll strip the bolt threads. These only need to be snug, not vise-like! Over tightening can also make the tuning go sharp, so you're undoing all your previous efforts.

It's the plate that does the work, not the bolt. Tighten until you feel some light resistance. That's all it needs.

_________________
"A little song. A little dance. A little seltzer down your pants." -Chuckles the Clown
Bendmaster - ISO Bendmaster setup videos Guitar10
GUITARS : https://legend.barryeames.com
MUSIC/PIX/VIDEOS: https://getback.barryeames.com (including Spectrum ST)
Barry
Barry
Hero, Legend, and all round good guy

Number of posts : 8796
Age : 79
Location : Port Weller, St. Catharines, Canada
Registration date : 2009-05-01

https://legend.barryeames.com

Back to top Go down

Bendmaster - ISO Bendmaster setup videos Empty Re: ISO Bendmaster setup videos

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum