Request for Wiring Intent Discussion and Wiring Chart
+5
corsair
Sgt. Vimes
gittarasaurus
IanO
Brainfertilizer
9 posters
Page 1 of 2
Page 1 of 2 • 1, 2
Request for Wiring Intent Discussion and Wiring Chart
So I am having a custom guitar built to celebrate my promotion 14 months ago. It is a friend doing it for me (Jon Kammerer), so since I know he's been struggling financially and busy getting his RN degree and a job so that he can make payments on his shop and not close down, I haven't pushed him to finish it.
I really like twang in a guitar, and late 80s hair metal sounds. I also like a good hard rock crunchy sound, like you'd dial in for a basic blues song. And I like Styx guitar sounds (which range from Tommy Shaw's double coils to James Young's strat sounds).
I like the switching flexibility you get from the Dynasty, in theory.
In practice, however, the phase reversal switch kinda leaves me cold.
But I was thinking that it would be cool to have Seymour Duncan P-rails with a Single Coil in the middle.
It seems like you could get some good sounds with a 3-way switch for each P-rail, a 3-way switch to select Bridge/Bridge+Neck/Neck for the P-rails, and a 2-way switch for the middle single coil on/off.
Is that too complicated? Is that the best way to get some good twang? Is there a better way to get good twang?
I've never played a P-90 equipped guitar before, but they describe it as a hot/dirty single coil. That's the way I think of Stevie Ray Vaughan's tone...am I off on that thought?
Should I skip the P-rail idea entirely and go with a normal H/S/S?
Should I skip the on/off for the middle pickup and just go with a normal 5-way plus a coil-tap switch?
Should I consider an H/S/S with the ability to switch between parallel and series in the humbucker? (like a 3-way that is Series-Parallel-Coil Tap, combined with a normal 3-way/5-way that can turn the pickup entirely off) With this 3-way, a 3-way switch to select B/B+N/N and an on-off switch for the middle single coil, I could conceivably have the humbucker in parallel (twangy, right?), plus the middle coil on (more twangy), plus the neck single coil (MOAR twangy to the point of tears), right? Or would it just sound like a muddy mess?
After we talk all this through and you guys beat some sense into me, I'll need someone (probably Guitarasaurus) to draw up a wiring diagram for me so I can give it to Jon.
Thanks...
I really like twang in a guitar, and late 80s hair metal sounds. I also like a good hard rock crunchy sound, like you'd dial in for a basic blues song. And I like Styx guitar sounds (which range from Tommy Shaw's double coils to James Young's strat sounds).
I like the switching flexibility you get from the Dynasty, in theory.
In practice, however, the phase reversal switch kinda leaves me cold.
But I was thinking that it would be cool to have Seymour Duncan P-rails with a Single Coil in the middle.
It seems like you could get some good sounds with a 3-way switch for each P-rail, a 3-way switch to select Bridge/Bridge+Neck/Neck for the P-rails, and a 2-way switch for the middle single coil on/off.
Is that too complicated? Is that the best way to get some good twang? Is there a better way to get good twang?
I've never played a P-90 equipped guitar before, but they describe it as a hot/dirty single coil. That's the way I think of Stevie Ray Vaughan's tone...am I off on that thought?
Should I skip the P-rail idea entirely and go with a normal H/S/S?
Should I skip the on/off for the middle pickup and just go with a normal 5-way plus a coil-tap switch?
Should I consider an H/S/S with the ability to switch between parallel and series in the humbucker? (like a 3-way that is Series-Parallel-Coil Tap, combined with a normal 3-way/5-way that can turn the pickup entirely off) With this 3-way, a 3-way switch to select B/B+N/N and an on-off switch for the middle single coil, I could conceivably have the humbucker in parallel (twangy, right?), plus the middle coil on (more twangy), plus the neck single coil (MOAR twangy to the point of tears), right? Or would it just sound like a muddy mess?
After we talk all this through and you guys beat some sense into me, I'll need someone (probably Guitarasaurus) to draw up a wiring diagram for me so I can give it to Jon.
Thanks...
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
Speak to the G man, He who speaketh drawings of infinite wisdom and folowabilityisms
IanO- Senior Member
- Number of posts : 259
Location : Cambridge U.K.
Registration date : 2011-02-04
Re: Request for Wiring Intent Discussion and Wiring Chart
Sure, but I'd like to get people's opinions of the best pickups or pickup configurations to get plenty o'twang, blues, and 80s hair band tone, all on one guitar.
It might be a ridiculous notion.
Or maybe someone has some ideas.
It might be a ridiculous notion.
Or maybe someone has some ideas.
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
just a couple thoughts...
most important to me is that the layout should be intuitive. so that most anyone, with a little experience, can easily understand the operations.
then when the variety of options is understood, that a quick look at the controls reveals what setup is active. so from the first note, you know what sound is going to come out.
i devised a rotary switch setup with 6 positions for a 2 humbucker guitar, but it was hard to tell what position the switch was in. and it needed more tweeking, because what seemed like a logical progression of settings in theory, did not produce a smooth progression of changes through all the settings. the sound texture and levels varied too much from one position to the next. so i think the more complex the setup, the more trial and error to fine tune it to a state of real utility.
most important to me is that the layout should be intuitive. so that most anyone, with a little experience, can easily understand the operations.
then when the variety of options is understood, that a quick look at the controls reveals what setup is active. so from the first note, you know what sound is going to come out.
i devised a rotary switch setup with 6 positions for a 2 humbucker guitar, but it was hard to tell what position the switch was in. and it needed more tweeking, because what seemed like a logical progression of settings in theory, did not produce a smooth progression of changes through all the settings. the sound texture and levels varied too much from one position to the next. so i think the more complex the setup, the more trial and error to fine tune it to a state of real utility.
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
So what do you recommend to make it more intuitive?
It seems to me that it should start with a 5-way switch, and then either mini-toggles or push/pull for some basic A/B switches. And then one two-way mini-toggle off to the side for the bypass/blower switch.
It seems to me that it should start with a 5-way switch, and then either mini-toggles or push/pull for some basic A/B switches. And then one two-way mini-toggle off to the side for the bypass/blower switch.
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
One pickup I like a lot that gave me twang was the DiMarzio HS-2, primarily a bridge pup, it works well in middle position, I had this setup on a s-h-s strat where the hs2 was auto-coil when in positions 2 and 4, and just plain hb when in middle. twas twangilicious.
Sgt. Vimes- Financial supporter
- Number of posts : 3322
Age : 53
Location : tyneside
Registration date : 2011-11-03
Re: Request for Wiring Intent Discussion and Wiring Chart
the location of the switch should help to convey what it's function is, where on the guitar, which way the bat swings.
when i played in a band i used the thunder IIA and i found the mini switches easy to use, and easy to see the position of everything all at one look. i never used a guitar with push/pulls to play on stage, but it seems more difficult to make quick switches in mid-song, or mid-solo. that may or may not be important to others and how they use the available settings
the thunder offered so many sounds, i tried to find a place to use all of them, somewhere in the different types of songs we played.
i like the way the dynasty, the spectrum and others have a 3-way switch for the neck and bridge and another switch to engage the middle pickup. i find that a better setup to make the change from bridge/mid to neck/mid. that is more how i would use my settings as opposed to mid pickup on/off. plus the extra setting of all-three-on that you don't get with a 5-way. what you don't get is middle only, but that is not a setting i use much for the style i play.
i guess something else to consider is what is the main thing you will use the guitar for? live performance, recording studio, garage jams...
one of my own-built guitars is way too heavy to stand and perform a set with, but i play sitting down at home nearly exclusively anymore, so no big deal. looks awesome, plays great, but heavy as a log. i never even put strap buttons on it.
when i played in a band i used the thunder IIA and i found the mini switches easy to use, and easy to see the position of everything all at one look. i never used a guitar with push/pulls to play on stage, but it seems more difficult to make quick switches in mid-song, or mid-solo. that may or may not be important to others and how they use the available settings
the thunder offered so many sounds, i tried to find a place to use all of them, somewhere in the different types of songs we played.
i like the way the dynasty, the spectrum and others have a 3-way switch for the neck and bridge and another switch to engage the middle pickup. i find that a better setup to make the change from bridge/mid to neck/mid. that is more how i would use my settings as opposed to mid pickup on/off. plus the extra setting of all-three-on that you don't get with a 5-way. what you don't get is middle only, but that is not a setting i use much for the style i play.
i guess something else to consider is what is the main thing you will use the guitar for? live performance, recording studio, garage jams...
one of my own-built guitars is way too heavy to stand and perform a set with, but i play sitting down at home nearly exclusively anymore, so no big deal. looks awesome, plays great, but heavy as a log. i never even put strap buttons on it.
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
Hmmm.... I played my VA900 onstage and in the studio for 20 some years and found, as guitarsaurus says, that finding your way around the multiple switching setup to be easier in the studio than live, even when I was extremely familiar with the instrument! So consider the sort of use this exciting new guitar is going to have!
Isn't the Tele twang and bark partly due to the metal bridge pickup surround?
Isn't the Tele twang and bark partly due to the metal bridge pickup surround?
corsair- Senior Member
- Number of posts : 6333
Age : 65
Location : Mount Hunter, NSW, Australia
Registration date : 2008-04-08
Re: Request for Wiring Intent Discussion and Wiring Chart
I've a Tanglewood Europa.
Top of the range in the early 90's metal guitar, Super Strat type thing.
It has h/s/h configuration, 1 volume, 1 tone, 5 way switch, pull/push on volume for a coil tap on the h/bukers.
pos.1 bridge h/b.
2, one coil on bridge/h/b and middle pup.
3, Both h/b's
4, mid and one coil on neck h/b
5, neck h/b.
Pull up the vol. coil tap
Real easy to use and goes from metal to Strat twang.
Pups are Kent Armstrong OTT's. (over the top)
The more switches and gadgets= more fiddling, less playing.
My 2 cents.
Top of the range in the early 90's metal guitar, Super Strat type thing.
It has h/s/h configuration, 1 volume, 1 tone, 5 way switch, pull/push on volume for a coil tap on the h/bukers.
pos.1 bridge h/b.
2, one coil on bridge/h/b and middle pup.
3, Both h/b's
4, mid and one coil on neck h/b
5, neck h/b.
Pull up the vol. coil tap
Real easy to use and goes from metal to Strat twang.
Pups are Kent Armstrong OTT's. (over the top)
The more switches and gadgets= more fiddling, less playing.
My 2 cents.
Re: Request for Wiring Intent Discussion and Wiring Chart
corsair wrote:Isn't the Tele twang and bark partly due to the metal bridge pickup surround?
Mainly due to the metal plate on the botton of the pup
Re: Request for Wiring Intent Discussion and Wiring Chart
I just jam with friends or on my own.
I am leaning toward the middle pickup on/off, too. It is nice to hear that is a favorite of other, more skilled/accomplished guitarists.
I am leaning toward the middle pickup on/off, too. It is nice to hear that is a favorite of other, more skilled/accomplished guitarists.
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
it might be that it is also wound fatter than a strat bridge pickup, usually over 7k ohms
tele pickups also use rod magnets, not a bar magnet and slugs.
tele pickups also use rod magnets, not a bar magnet and slugs.
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
Nowadays pickup selection is immense.
Spoilt for choice eh!
Spoilt for choice eh!
Re: Request for Wiring Intent Discussion and Wiring Chart
Hi again,, sorry I did mean to add a couple of pences worth of personal opinion but had to collect my daughter from Girls Brigade and pressed send before I had realised it.
I had no particular issues with theSC twanginess of my strat apart from the weaker sounding bridge pick-up (i replaced it with an alnico pro). A couple of weeks ago I added an extra single coil to my Strat for 3 reasons:
1, I found the S/C at the bridge just not ROCK enough for the moments when I wanted it! and
2, I had the original fender SC in a box as the brigge pickup in the guitar is a SD alnico pro that I fitted as a part cure to point 1.
3, I had bought a new soldering iron and had been inspied to customise by others on the Forum.
Here's a piccy: https://s1151.photobucket.com/user/molecularelk/media/Image0224.jpg.html?sort=3&o=0
The new p/up only works when the mini switch nearest the Volume pot is switched either forward -series or back -parrellel and is disengaged when the 5 way is moved off of pos 1, This give me the Stock set-up with the benefit of a "thicker/meatier series HB tone or twangier parrallel HB tone - me likey this velly much!
The lower Mini switch is in/out of phase and an effect that I still am not sure about! All things get very thin'n'weedy and not entirely in a good way.....but I can't be bothered to remove it so it shall stay. In the pic it's in weedy mode (forward) so it's not easy to accidently go weedy at the wrong moment.
In fact the only use I have found for it is during those moments when you can turn the amp up, Its great to play a riff out of phase for an a pre-intro then come in on full HB or SC mode
Not sure if this helps you at all but feel free to ask if you want any more info.
Cheers
Ian
PS...thanks once again Gittarasaurus
I had no particular issues with theSC twanginess of my strat apart from the weaker sounding bridge pick-up (i replaced it with an alnico pro). A couple of weeks ago I added an extra single coil to my Strat for 3 reasons:
1, I found the S/C at the bridge just not ROCK enough for the moments when I wanted it! and
2, I had the original fender SC in a box as the brigge pickup in the guitar is a SD alnico pro that I fitted as a part cure to point 1.
3, I had bought a new soldering iron and had been inspied to customise by others on the Forum.
Here's a piccy: https://s1151.photobucket.com/user/molecularelk/media/Image0224.jpg.html?sort=3&o=0
The new p/up only works when the mini switch nearest the Volume pot is switched either forward -series or back -parrellel and is disengaged when the 5 way is moved off of pos 1, This give me the Stock set-up with the benefit of a "thicker/meatier series HB tone or twangier parrallel HB tone - me likey this velly much!
The lower Mini switch is in/out of phase and an effect that I still am not sure about! All things get very thin'n'weedy and not entirely in a good way.....but I can't be bothered to remove it so it shall stay. In the pic it's in weedy mode (forward) so it's not easy to accidently go weedy at the wrong moment.
In fact the only use I have found for it is during those moments when you can turn the amp up, Its great to play a riff out of phase for an a pre-intro then come in on full HB or SC mode
Not sure if this helps you at all but feel free to ask if you want any more info.
Cheers
Ian
PS...thanks once again Gittarasaurus
IanO- Senior Member
- Number of posts : 259
Location : Cambridge U.K.
Registration date : 2011-02-04
Re: Request for Wiring Intent Discussion and Wiring Chart
Yup. Quite a bit to do with it.corsair wrote:...Isn't the Tele twang and bark partly due to the metal bridge pickup surround?
_________________
"A little song. A little dance. A little seltzer down your pants." -Chuckles the Clown
GUITARS : https://legend.barryeames.com
MUSIC/PIX/VIDEOS: https://getback.barryeames.com (including Spectrum ST)
Re: Request for Wiring Intent Discussion and Wiring Chart
IanO wrote:Hi again,, sorry I did mean to add a couple of pences worth of personal opinion but had to collect my daughter from Girls Brigade and pressed send before I had realised it.
I had no particular issues with theSC twanginess of my strat apart from the weaker sounding bridge pick-up (i replaced it with an alnico pro). A couple of weeks ago I added an extra single coil to my Strat for 3 reasons:
1, I found the S/C at the bridge just not ROCK enough for the moments when I wanted it! and
2, I had the original fender SC in a box as the brigge pickup in the guitar is a SD alnico pro that I fitted as a part cure to point 1.
3, I had bought a new soldering iron and had been inspied to customise by others on the Forum.
Here's a piccy: https://s1151.photobucket.com/user/molecularelk/media/Image0224.jpg.html?sort=3&o=0
The new p/up only works when the mini switch nearest the Volume pot is switched either forward -series or back -parrellel and is disengaged when the 5 way is moved off of pos 1, This give me the Stock set-up with the benefit of a "thicker/meatier series HB tone or twangier parrallel HB tone - me likey this velly much!
The lower Mini switch is in/out of phase and an effect that I still am not sure about! All things get very thin'n'weedy and not entirely in a good way.....but I can't be bothered to remove it so it shall stay. In the pic it's in weedy mode (forward) so it's not easy to accidently go weedy at the wrong moment.
In fact the only use I have found for it is during those moments when you can turn the amp up, Its great to play a riff out of phase for an a pre-intro then come in on full HB or SC mode
Not sure if this helps you at all but feel free to ask if you want any more info.
Cheers
Ian
PS...thanks once again Gittarasaurus
That's pretty cool.
I'm not sure it is what I'm looking for though.
I really want to be able to get the coil nearest the bridge + the neck single coil at the same time, for max twang. I like the switch for series/parallel for the bridge, but maybe it should be a three position toggle: coil tap, series, parallel, plus an/off mini-switch to turn on the middle pickup plus a Gibson 3-way to switch between bridge only, bridge + neck, neck only.
Finally, a 3rd mini-switch to go bypass.
Gittarasaurus, would that be a difficult wiring chart? Especially now that I've finally figured out how to spell your screen name?
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
looking closely at seymour duncan website info, it says this:
"P-Rails are different to most humbuckers. In a normal humbucker, a screw coil will always cancel with a slug coil – whether from the same pickup or another humbucker. However, with the P-Rails, they’re set up so that the same coils will cancel each other’s hum. So two P-90s together will cancel hum, as will two rail coils."
with pickups built in this way, a middle pickup will sound very different when added to each of the other pickups. it will be out-of-phase with one of them and produce a very diminished signal.
the other thing i found interesting was the triple shot mounting rings. they could give you most of the options you are looking for (series,parallel,rail,both,P90). they look to be very, very simple to hook up. when using those rings for output configuration, you will need to use only a common pickup selector switch. $50 seems a bit much for trim rings, but 4 mini switches and 2 trim rings, well, that is not too much. and as easy as they seem to be, it is a winner in my book. and they seem to be nearly invisible once installed. i just don't know about how easy it is to operate the switches when playing, but overall it looks like a good innovation.
another very cool thing i noticed about the triple shot mounting rings, is that they will fit standard humbuckers, so can be used on any 4-wire humbucker pickup.
"P-Rails are different to most humbuckers. In a normal humbucker, a screw coil will always cancel with a slug coil – whether from the same pickup or another humbucker. However, with the P-Rails, they’re set up so that the same coils will cancel each other’s hum. So two P-90s together will cancel hum, as will two rail coils."
with pickups built in this way, a middle pickup will sound very different when added to each of the other pickups. it will be out-of-phase with one of them and produce a very diminished signal.
the other thing i found interesting was the triple shot mounting rings. they could give you most of the options you are looking for (series,parallel,rail,both,P90). they look to be very, very simple to hook up. when using those rings for output configuration, you will need to use only a common pickup selector switch. $50 seems a bit much for trim rings, but 4 mini switches and 2 trim rings, well, that is not too much. and as easy as they seem to be, it is a winner in my book. and they seem to be nearly invisible once installed. i just don't know about how easy it is to operate the switches when playing, but overall it looks like a good innovation.
another very cool thing i noticed about the triple shot mounting rings, is that they will fit standard humbuckers, so can be used on any 4-wire humbucker pickup.
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
The guitar I want to put them on wouldn't really look good with the triple shot mounting rings.
Also, I don't understand pickup wiring enough to instinctively understand the out-of-phase problem. Is there any way to switch the phase of the middle pickup to be back in phase? That's what the third push/pull on the Dimension IV/Dynasty does, right?
Also, I don't understand pickup wiring enough to instinctively understand the out-of-phase problem. Is there any way to switch the phase of the middle pickup to be back in phase? That's what the third push/pull on the Dimension IV/Dynasty does, right?
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
the seymour duncan pickups seem to have been designed to be installed in pairs. one pickup is reverse-wound-reverse-polarity to the other, so they act as noise cancelling when connected together. so any other pickup added to the matched pair will have to deal with that issue.
the neck and bridge pickups on a Dynasty are built to be the same pickup basically, so the middle pickup has a consistent phase relation to both the other pickups. when the reverse phase switch is engaged, then it still has a consistent relation to each of the other pickups.
you could resolve that issue with the P-Rails by simply using 2 neck pups or 2 bridge pups. in order to get the noise canceling effect, the magnetic polarity of the middle pickup should be opposite of the others, so if the middle has a south-up magnet, the p-rails should have a north-up.
i'm not sure if there is that much detail in the specifications that come with most pickups, but you may be able to find out thru some technical support contact. you could choose neck or bridge, whichever would be a correct match for your middle pup.
the neck and bridge pickups on a Dynasty are built to be the same pickup basically, so the middle pickup has a consistent phase relation to both the other pickups. when the reverse phase switch is engaged, then it still has a consistent relation to each of the other pickups.
you could resolve that issue with the P-Rails by simply using 2 neck pups or 2 bridge pups. in order to get the noise canceling effect, the magnetic polarity of the middle pickup should be opposite of the others, so if the middle has a south-up magnet, the p-rails should have a north-up.
i'm not sure if there is that much detail in the specifications that come with most pickups, but you may be able to find out thru some technical support contact. you could choose neck or bridge, whichever would be a correct match for your middle pup.
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
Got it. That makes sense, and is very helpful.
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
I am 90% certain this is what I want:
I know I want an H/S/S configuration, basically.
I want the bridge HB and neck Single Coil to be controlled by a Gibson-style 3-way (your normal 3-way switch).
I want the middle single coil to be controlled by an on/off 2-way mini-switch.
I want a bypass switch that bypasses all tone/volume/switches.
Things I'm not sure of:
Do I want a traditional HB or a P-Rails in the bridge?
Do I want a tradition single coil or a P-90 in the neck?
Do I want the bypass switch to be just the bridge pickup, or all the pickups?
If I want a P-Rail, do I want you to use the Triple Shot Rings or a separate 3-way mini-toggle?
I know I want an H/S/S configuration, basically.
I want the bridge HB and neck Single Coil to be controlled by a Gibson-style 3-way (your normal 3-way switch).
I want the middle single coil to be controlled by an on/off 2-way mini-switch.
I want a bypass switch that bypasses all tone/volume/switches.
Things I'm not sure of:
Do I want a traditional HB or a P-Rails in the bridge?
Do I want a tradition single coil or a P-90 in the neck?
Do I want the bypass switch to be just the bridge pickup, or all the pickups?
If I want a P-Rail, do I want you to use the Triple Shot Rings or a separate 3-way mini-toggle?
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
Westbone wrote:What does your guitar maker think?
If I give him a wiring diagram, he'll do it for me. He puts more of his thought into the guitar design and construction than the pickup configuration.
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
you are going to drop a good bit of money on your custom built guitar. how about a little bit of $$ to give a real tryout to some of the combinations you are considering
maybe you can find a beater guitar for cheap, and try out some of the pickup combinations. there are squier guitars available on craigslist here for $50 almost every day. i have found first act to be a good solid test-bed guitars, as well (i also have one from their custom shop, very nice inDD!). i have an aria pro II STG series ($50) i also use to experiment
it doesn't have to be a pretty job to get some real ear-time for the pickups and/or switches.
pickguards, swimming pool routing, make changes much easier. rough cuts, missing screws don't matter, you just need enough to hold it in there for a test drive.
maybe you can find a beater guitar for cheap, and try out some of the pickup combinations. there are squier guitars available on craigslist here for $50 almost every day. i have found first act to be a good solid test-bed guitars, as well (i also have one from their custom shop, very nice inDD!). i have an aria pro II STG series ($50) i also use to experiment
it doesn't have to be a pretty job to get some real ear-time for the pickups and/or switches.
pickguards, swimming pool routing, make changes much easier. rough cuts, missing screws don't matter, you just need enough to hold it in there for a test drive.
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
I suggest that trying to do it all with one guitar is not the way to go. I have tried it many times - I wanted what you want.
In the end, it's just easier to do it with 2-3 different guitars - for me.
In the end, it's just easier to do it with 2-3 different guitars - for me.
colt933- Senior Member
- Number of posts : 583
Registration date : 2008-04-08
Re: Request for Wiring Intent Discussion and Wiring Chart
Brain Fertilizer wrote:Westbourne wrote:What does your guitar maker think?
If I give him a wiring diagram, he'll do it for me. He puts more of his thought into the guitar design and construction than the pickup configuration.
Yeah, but he's gotta make room for all this. Accommodate all these switches.
Re: Request for Wiring Intent Discussion and Wiring Chart
Westbone wrote:Brain Fertilizer wrote:
If I give him a wiring diagram, he'll do it for me. He puts more of his thought into the guitar design and construction than the pickup configuration.
Yeah, but he's gotta make room for all this. Accommodate all these switches.
It shouldn't be a problem, but that's worth remembering.
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
Just for clarity, The upper miniswitch is a 3 way, Parrallel HB/original S/C/ series HB.
Surely a miniswitch could be added to bypass straight to the BR + NK coils sound overiding the 5way (or other Pup switch) position?
Gittarasaurus?
The old "3 way for each pickup" would surely be easiest for mixing Pups/sounds........ but not the easiest for use in action
If I was going custom I would drop in a pair of P-rails and a middle s/c, Strat, LP, thunder 1 all in one!
Ian
Surely a miniswitch could be added to bypass straight to the BR + NK coils sound overiding the 5way (or other Pup switch) position?
Gittarasaurus?
The old "3 way for each pickup" would surely be easiest for mixing Pups/sounds........ but not the easiest for use in action
If I was going custom I would drop in a pair of P-rails and a middle s/c, Strat, LP, thunder 1 all in one!
Ian
IanO- Senior Member
- Number of posts : 259
Location : Cambridge U.K.
Registration date : 2011-02-04
Re: Request for Wiring Intent Discussion and Wiring Chart
Not started yet, but will be started within a week.Westbone wrote:At what stage is the construction at?
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
not just for little kids...
first act custom shop guitar
nice semi-hollow body, controls are volume/volume/tone (no switch)
these humbuckers kick butt too
first act custom shop guitar
nice semi-hollow body, controls are volume/volume/tone (no switch)
these humbuckers kick butt too
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
Here's what I think I want:
Bridge humbucker
Middle single coil
Neck P-90
5-way Blade Switch:
1: Bridge series
2: Bridge parallel
3: Bridge tapped to single coil
4: Bridge single coil + neck
5: Neck
2-way mini-toggle:
Middle single coil on/off
Gibson 3-way toggle:
up: bypass for bridge parallel only
middle: no bypass
down: bypass for neck P-90 only
Gitarrasaurus (and others),
Is this feasible and rational?
Which combinations would be hum-cancelling?
Would it end up with any horrible, weak, or tinny sounds?
Any suggestions for modifications from this?
Bridge humbucker
Middle single coil
Neck P-90
5-way Blade Switch:
1: Bridge series
2: Bridge parallel
3: Bridge tapped to single coil
4: Bridge single coil + neck
5: Neck
2-way mini-toggle:
Middle single coil on/off
Gibson 3-way toggle:
up: bypass for bridge parallel only
middle: no bypass
down: bypass for neck P-90 only
Gitarrasaurus (and others),
Is this feasible and rational?
Which combinations would be hum-cancelling?
Would it end up with any horrible, weak, or tinny sounds?
Any suggestions for modifications from this?
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
can you explain a little bit of what you mean when you say 'bypass'.
do you mean to override all other settings(vol,tone,switches) and put the chosen pup directly to the output jack?
looks like if you add the middle pup to pos 3, 4, 5 you would get some noise cancelling, and the humbucker will take care of it in pos 1, 2.
doesn't appear that any positions will give weak or diminished output.
do you mean to override all other settings(vol,tone,switches) and put the chosen pup directly to the output jack?
looks like if you add the middle pup to pos 3, 4, 5 you would get some noise cancelling, and the humbucker will take care of it in pos 1, 2.
doesn't appear that any positions will give weak or diminished output.
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
Yep, by bypass I mean I want override ALL other settings and put the chosen pup directly to the output jack.
I have it on two guitars (stock on the Cort Garage2 Matthias Jabs signature, aftermarket on my Yamaha RGX 1212S). It is pretty cool, works well for when you want to pump up the output for a solo section, or a hard bridge in a softer song.
I have it on two guitars (stock on the Cort Garage2 Matthias Jabs signature, aftermarket on my Yamaha RGX 1212S). It is pretty cool, works well for when you want to pump up the output for a solo section, or a hard bridge in a softer song.
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
Can you write me up a wiring diagram for this?
I'll buy you a beer the next (first) time we meet...
I'll buy you a beer the next (first) time we meet...
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
i'll doodle some and see what i can figure out. probably be later tonite or tomorrow before i can work it up.
on wednesdays i'm a volunteer sponsor at the elementary school garden, i teach a group of fourth and fifth grade students about gardening and related topics. today we are starting seeds for the summer garden. yeeeehaa! so i'll be busy with that until the end of the school day. then homework with my kid and all that routine.
i might ask some more questions along the way...
on wednesdays i'm a volunteer sponsor at the elementary school garden, i teach a group of fourth and fifth grade students about gardening and related topics. today we are starting seeds for the summer garden. yeeeehaa! so i'll be busy with that until the end of the school day. then homework with my kid and all that routine.
i might ask some more questions along the way...
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
here's one already..... controls?
are you going to use master volume/ master tone
are you going to use master volume/ master tone
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
gittarasaurus wrote:i'll doodle some and see what i can figure out. probably be later tonite or tomorrow before i can work it up.
on wednesdays i'm a volunteer sponsor at the elementary school garden, i teach a group of fourth and fifth grade students about gardening and related topics. today we are starting seeds for the summer garden. yeeeehaa! so i'll be busy with that until the end of the school day. then homework with my kid and all that routine.
i might ask some more questions along the way...
6 inches of new snow in the past 4 days and I still got my RoMas workin'...
Re: Request for Wiring Intent Discussion and Wiring Chart
No rush.
1V, 1T.
I'm not much of a reduced tone guy. I could almost get away with no T at all, except there are some times where I want to roll off the tone slightly to reduce brittleness when mic'd.
But most of the time I do tone adjustments on the amp.
What I'm getting at is that I don't know how to use more than one Tone knob effectively, so why have more than one?
1V, 1T.
I'm not much of a reduced tone guy. I could almost get away with no T at all, except there are some times where I want to roll off the tone slightly to reduce brittleness when mic'd.
But most of the time I do tone adjustments on the amp.
What I'm getting at is that I don't know how to use more than one Tone knob effectively, so why have more than one?
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
still a couple things to work on a bit more...
i have the 5-way switch connections figured out, just trying to figure how to accomplish all the bypass operations.
you mentioned the bypass should be a gibson 3-way type (normally that would be a SPDT, 3-pos, on/on/on) - * do you simply mean you want to see a 3 position switch with a large bat handle on it?
switches are available with multiple sets of contacts, but the selection of handle types may be more limited for the more complex switches.
looking at the bypass switching - * do you want to prohibit the middle pickup from working when a bypass position is selected?
because the humbucker must be caused to become a parallel connection when the bypass is engaged, (overriding the position of the other switches), more contacts are needed than a single SPDT to do that with one throw of one switch, and even more if you want to prohibit the middle pickup.
it is additionally more complex because when the same switch is thrown to the other end, you are looking for a different pickup to come on, but to cause similar exclusions.
it would not be difficult to simply bypass the vol/tone, but with the extra default actions required when changing to bypass, more contacts are needed.
i have the 5-way switch connections figured out, just trying to figure how to accomplish all the bypass operations.
you mentioned the bypass should be a gibson 3-way type (normally that would be a SPDT, 3-pos, on/on/on) - * do you simply mean you want to see a 3 position switch with a large bat handle on it?
switches are available with multiple sets of contacts, but the selection of handle types may be more limited for the more complex switches.
looking at the bypass switching - * do you want to prohibit the middle pickup from working when a bypass position is selected?
because the humbucker must be caused to become a parallel connection when the bypass is engaged, (overriding the position of the other switches), more contacts are needed than a single SPDT to do that with one throw of one switch, and even more if you want to prohibit the middle pickup.
it is additionally more complex because when the same switch is thrown to the other end, you are looking for a different pickup to come on, but to cause similar exclusions.
it would not be difficult to simply bypass the vol/tone, but with the extra default actions required when changing to bypass, more contacts are needed.
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
Okay, no need for an actual Gibson 3-way, I did just mean a 3 position switch with a large bat handle. The 3-way mini-switches usually take more effort and care to get to the middle position. But I can go with a 3-way mini-switch if that's necessary.
Since the bypass is so complicated to restrict just to the specific pickup, then just make it a V/T bypass. So in that case, it can just be a 2-way on/off.
That should simplify things, right?
Thanks for going to the effort for me.
Since the bypass is so complicated to restrict just to the specific pickup, then just make it a V/T bypass. So in that case, it can just be a 2-way on/off.
That should simplify things, right?
Thanks for going to the effort for me.
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
some people like to do crossword puzzles....
i'm a wire nut, guitar geek. i find it fun, interesting, challenging, to develop alternative switching concepts and new wiring designs.
i'm a wire nut, guitar geek. i find it fun, interesting, challenging, to develop alternative switching concepts and new wiring designs.
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
So what do you think of this one?
Clever?
Useful?
Silly?
Unnecessary?
Clever?
Useful?
Silly?
Unnecessary?
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
Might it be useful to have a miniswitch for each pickup sending either through or past the V/T circuit. You could then send them indvidually?
Just thinking out loud
Ian
Just thinking out loud
Ian
IanO- Senior Member
- Number of posts : 259
Location : Cambridge U.K.
Registration date : 2011-02-04
Re: Request for Wiring Intent Discussion and Wiring Chart
Just had another thought.
What about this?
Same pickups (bridge HB, middle single coil, neck P-90).
5-way strat blade switch
3 2-way mini-toggles.
5-way:
1: Bridge only series
2: Bridge only parallel
3: Bridge only north single coil
4: Bridge only south single coil
5: Bridge off
mini-toggle 1: on/off middle single coil
mini-toggle 2: on/off neck single coil
mini-toggle 3: bypass V/T
Would that be more complicated or less complicated?
I threw in the "north single coil/south single coil" for positions 3 and 4 of the 5-way because I'm not sure what else to do with it. I'm open to suggestions for what to do with Position 4 if there is no real difference which coil is cut and position 3 is the single coil cut position.
The point is, it might be cool to have the ability to combine the neck P-90 with the different HB combinations. It would sound different to have a HB series + P-90 vs a HB parallel + P-90 or HB single coil + P-90, right?
But if it just complicates things, then never mind.
What about this?
Same pickups (bridge HB, middle single coil, neck P-90).
5-way strat blade switch
3 2-way mini-toggles.
5-way:
1: Bridge only series
2: Bridge only parallel
3: Bridge only north single coil
4: Bridge only south single coil
5: Bridge off
mini-toggle 1: on/off middle single coil
mini-toggle 2: on/off neck single coil
mini-toggle 3: bypass V/T
Would that be more complicated or less complicated?
I threw in the "north single coil/south single coil" for positions 3 and 4 of the 5-way because I'm not sure what else to do with it. I'm open to suggestions for what to do with Position 4 if there is no real difference which coil is cut and position 3 is the single coil cut position.
The point is, it might be cool to have the ability to combine the neck P-90 with the different HB combinations. It would sound different to have a HB series + P-90 vs a HB parallel + P-90 or HB single coil + P-90, right?
But if it just complicates things, then never mind.
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
i don't think there will be a significant change in tone when choosing one coil or the other on a split humbucker, unless there is a major difference between the two coils. i think you could call that, a distinction without a difference.
here's a couple ideas;
have you seen the Freeway Switch that stew-mac sells? looks just like a typical 3-way gibson style switch, but does much more
skip down to the 4th drawing, labeled H/H/H with twin vol/tone. ignore the vol/tone wiring for now.
you can use this switch schematic to do much of what you want.
pos1,2,3, gives you a 3-way on/on/on for neck and bridge
pos4,5,6 adds the middle pup to all three positions
now if you add in a mini switch for the bridge humbucker like this, you can have all those options in each one of the bridge-pup-on settings from the Freeway switch
you could then add in a vol/tone bypass switch if you wanted to, and you are only up to 3 switches total; selector switch, bridge connections, bypass
here's a couple ideas;
have you seen the Freeway Switch that stew-mac sells? looks just like a typical 3-way gibson style switch, but does much more
skip down to the 4th drawing, labeled H/H/H with twin vol/tone. ignore the vol/tone wiring for now.
you can use this switch schematic to do much of what you want.
pos1,2,3, gives you a 3-way on/on/on for neck and bridge
pos4,5,6 adds the middle pup to all three positions
now if you add in a mini switch for the bridge humbucker like this, you can have all those options in each one of the bridge-pup-on settings from the Freeway switch
you could then add in a vol/tone bypass switch if you wanted to, and you are only up to 3 switches total; selector switch, bridge connections, bypass
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Re: Request for Wiring Intent Discussion and Wiring Chart
I like it.
I'm a little scared that it might be difficult to find the right position at a gig...but I'm willing to take that risk.
Since the diagrams don't have exactly what I want, can you draw up a diagram for this?
1T, 1V
1: Bridge only series
2: Bridge only parallel
3: Bridge only single coil (coil closest to bridge)
4: Bridge series + neck
5: Bridge parallel + neck
6: Bridge single coil + neck
mini-switch 1: on/off middle single coil
mini-switch 2: bypass T/V
That would do it, perfectly.
I'm a little scared that it might be difficult to find the right position at a gig...but I'm willing to take that risk.
Since the diagrams don't have exactly what I want, can you draw up a diagram for this?
1T, 1V
1: Bridge only series
2: Bridge only parallel
3: Bridge only single coil (coil closest to bridge)
4: Bridge series + neck
5: Bridge parallel + neck
6: Bridge single coil + neck
mini-switch 1: on/off middle single coil
mini-switch 2: bypass T/V
That would do it, perfectly.
Brainfertilizer- Senior Member
- Number of posts : 525
Registration date : 2011-05-04
Re: Request for Wiring Intent Discussion and Wiring Chart
i'll see what i can doodle out of it...
i've been trying to figure some different uses for the Freeway switch than what they have drawn up, so this is a good trial run.
i think you will be pleased with the action on the freeway switch. the contacts for soldering are a bit delicate, but the switch bat feels solid, and the positions notch in place well.
i actually have one on hand for a project guitar i occasionally work on. it is nowhere near needing the switch installed, so if you want to handle one and see if you think it feels good enough to use on your guitar, a couple bucks shipping each way is much less than the purchase price($21 +shipping) of a switch you don't want to use.
i've been trying to figure some different uses for the Freeway switch than what they have drawn up, so this is a good trial run.
i think you will be pleased with the action on the freeway switch. the contacts for soldering are a bit delicate, but the switch bat feels solid, and the positions notch in place well.
i actually have one on hand for a project guitar i occasionally work on. it is nowhere near needing the switch installed, so if you want to handle one and see if you think it feels good enough to use on your guitar, a couple bucks shipping each way is much less than the purchase price($21 +shipping) of a switch you don't want to use.
gittarasaurus- Financial supporter
- Number of posts : 1519
Location : San Francisco, CA
Registration date : 2011-05-25
Page 1 of 2 • 1, 2
Similar topics
» Wiring a 3 way toggle switch for series wiring
» MMK 61 wiring for PEQ
» Westone Spectrum MX Wiring Diagram
» New wiring project
» Rewiring the MMK45s in a Thunder 1
» MMK 61 wiring for PEQ
» Westone Spectrum MX Wiring Diagram
» New wiring project
» Rewiring the MMK45s in a Thunder 1
Page 1 of 2
Permissions in this forum:
You cannot reply to topics in this forum
|
|