Concord ii - Tremelo Arm

Go down

Concord ii - Tremelo Arm

Post by Donn on Fri Jan 04, 2019 7:02 am

Hoping somebody may be able to assist. Does anybody have a tremelo arm for a Concord 2-T? If not, what is the thread size for a 3rd party replacement? Also, once I do either find the original or buy a replacement, is there a particular way it should be fitted? I seem to remember when I did have it and screwed it in it didn't really have a huge effect. I am guessing there may be more to it than just putting it back in. I am a total novice so apologies if all this sounds a bit simple.
avatar
Donn
Newbie

Number of posts : 2
Registration date : 2019-01-04

Back to top Go down

Re: Concord ii - Tremelo Arm

Post by Barry on Fri Jan 04, 2019 11:20 am

Hi Donn and welcome.

I have only one Concord and it does not have the tremolo bridge, but unless someone corrects me, the majority of Westone arms are 6mm diameter ("import" size on most suppliers' web sites) and should fit.

There are some odd Westones which take a 10-32 thread and this may be one of them. Get a couple of bolts from the hardware store, 6mm and 10-32 that would give you a quick check before ordering anything.


StewMac, GuitarFetish, All Parts, etc. should be able to offer what you need.

_________________
"A little song. A little dance. A little seltzer down your pants." -Chuckles the Clown

GUITARS : http://legend.barryeames.com/guitars.html
MUSIC/PIX/VIDEOS: http://getback.barryeames.com (including Spectrum ST)
avatar
Barry
Hero, Legend, and all round good guy

Number of posts : 7245
Age : 73
Location : Port Weller, St. Catharines, Canada
Registration date : 2009-05-01

http://www.barryeames.com

Back to top Go down

Re: Concord ii - Tremelo Arm

Post by Donn on Fri Jan 04, 2019 11:29 am

Thanks Barry, I shall have a look and try a couple of bolts as you suggest.
With regards the fitting of the arm, is there anything specific or does it just screw in?
avatar
Donn
Newbie

Number of posts : 2
Registration date : 2019-01-04

Back to top Go down

Re: Concord ii - Tremelo Arm

Post by Westbone on Fri Jan 04, 2019 5:17 pm

If in the UK? try these 6 mm a perfect fit, all hardware is metric.

link
avatar
Westbone
Financial supporter

Number of posts : 5424
Location : Redbridge
Registration date : 2008-12-28

http://www.chruler.com/

Back to top Go down

Re: Concord ii - Tremelo Arm

Post by Barry on Sat Jan 05, 2019 12:02 pm

There ya go Donn, confirmed! 6mm it is for the Concord trem.

Thanks Damian Hello Wave

_________________
"A little song. A little dance. A little seltzer down your pants." -Chuckles the Clown

GUITARS : http://legend.barryeames.com/guitars.html
MUSIC/PIX/VIDEOS: http://getback.barryeames.com (including Spectrum ST)
avatar
Barry
Hero, Legend, and all round good guy

Number of posts : 7245
Age : 73
Location : Port Weller, St. Catharines, Canada
Registration date : 2009-05-01

http://www.barryeames.com

Back to top Go down

Re: Concord ii - Tremelo Arm

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum